tag:blogger.com,1999:blog-9074654920193695267.post2132337492209074843..comments2023-12-24T12:05:31.362+11:00Comments on BYLONG: After a Little ShuntingRay Phttp://www.blogger.com/profile/16624865987062727847noreply@blogger.comBlogger6125tag:blogger.com,1999:blog-9074654920193695267.post-65738322831854834472016-11-01T11:03:12.598+11:002016-11-01T11:03:12.598+11:00Tom, no room for a separate ash/coal siding unfort...Tom, no room for a separate ash/coal siding unfortunately and the visibility issue for shunting decided against a shortened carriage shed. Thanks for the info though.<br /><br />Regarding the shunting. there is always more than one way as we know. This was just a one off shunt and I haven't revisited it to try again and did originally want a railmotor/car siding.<br /><br />Regards,<br />RayRay Phttps://www.blogger.com/profile/16624865987062727847noreply@blogger.comtag:blogger.com,1999:blog-9074654920193695267.post-87749503788777625062016-11-01T09:03:54.995+11:002016-11-01T09:03:54.995+11:00Ray,
Data Sheets Drawing No. L8 - Carriage Shed c...Ray,<br /><br />Data Sheets Drawing No. L8 - Carriage Shed c1900 and 1910 provides both a skillion and gable roof type, single road carriage shed.<br /><br />The standard shed length is noted as being 150'-1", so you are right a bit big for Cassilis, you could halve / compress it to cover just a single 72'-6" car / ACS perhaps?<br /><br />A quick check of the ARHS Signal diagram Vol.3 CD Rom, I noted 14 locations that were provided with a single road carriage shed and only eleven of those were branch line terminus locations (and mostly in the hot north western regions).<br /><br />The remainder of branch line terminus locations did not have any specific carriage siding that I could see. Most though had an ash / coal siding in loco. So am sure crews would have been inventive and used "local rules" to get their required shunting done as you did placing the HCX into the wheat siding (if it wasn't being used).<br /><br />Would an alternative have been in this instance to run around, couple onto the SHG, ensure passengers have detrained and out-of's unloaded, draw back, then propel train forward into loco siding to detach the required S trucks, then withdraw and continue making up the return train.<br /><br />But then the S trucks in Loco would need to be moved so as to be able to turn the loco for the return trip?<br /><br />Hope this is of interest.<br /><br />regards,<br /><br />Tom. R.<br /><br /><br /><br /><br /> Tomhttps://www.blogger.com/profile/17574731499433982697noreply@blogger.comtag:blogger.com,1999:blog-9074654920193695267.post-72624773454057770392016-10-30T19:41:12.258+11:002016-10-30T19:41:12.258+11:00Colin
Thanks for the input. I have decided that t...Colin<br /><br />Thanks for the input. I have decided that there will be no shed as it would obstruct the view of the headshunt/yard end lead and tend to take away the wide open look of a branch terminus.<br /><br />No room for a dock road either.<br /><br />RayRay Phttps://www.blogger.com/profile/16624865987062727847noreply@blogger.comtag:blogger.com,1999:blog-9074654920193695267.post-35301199880784931882016-10-30T18:27:47.990+11:002016-10-30T18:27:47.990+11:00Ray
Not every location that had carriage dropped ...Ray<br /><br />Not every location that had carriage dropped off had a carriage shed. IIRC Coonabarrabran had the mail arrive with 2 carriages sometimes 3, the 30T would become the Coona shunt engine with the carriages left either at the station, not an issue on the day the Gwabegar service ran.<br /><br />Other locations left them in a siding near the station, some had a dock road for a carriage or two.<br /><br />Narrabri had a carriage shed which was basic for a single carriage that came off the mail of a morning, do not remember there being any platforms to clean it as the station staff had to clean the inside only, it was located on the eastern side of the loop.<br /><br />Unless you desire a shed, a simple dock road at one end of the platform might suffice, with access to the carriage itself from the platform and not to the van. Remember Wollongong had that arrangement on the down, at the Bomaderry end.Colin Husseyhttps://www.blogger.com/profile/10166476334786660482noreply@blogger.comtag:blogger.com,1999:blog-9074654920193695267.post-7672838190623899282016-10-30T17:09:49.101+11:002016-10-30T17:09:49.101+11:00Thanks for that, it is a long time since I visited...Thanks for that, it is a long time since I visited the site and a lot more documents have been listed. I found the plan but it is too long for the area I have so the passenger car/railmotor will just have to sit out in the sun.<br /><br />I did enjoy myself looking at some of the documents though.<br /><br />RayRay Phttps://www.blogger.com/profile/16624865987062727847noreply@blogger.comtag:blogger.com,1999:blog-9074654920193695267.post-18919358576926854812016-10-29T23:23:35.987+11:002016-10-29T23:23:35.987+11:00For plans for the shed try the coals to newcastle ...For plans for the shed try the coals to newcastle site found this the other week when i was looking for plans for a engine shed . Just look under documents and scroll down to nswgr plans then 1972 station plans there are plenty of plans there for most of the nsw buildings and trackside infrastructure. Hope this helps. <br />BoolyBoolyhttps://www.blogger.com/profile/11596391852477755296noreply@blogger.com